Model 1 - 8DEC

Cleans and profiles floor surfaces to the edge of side walls. Can clean to within 1 1/2" of front wall surface
Side magnetic seals can be removed for edging or attached for blasting in open areas. Blast pattern accuracy and wide abrasive selection allows users to achieve profiles around edges consistent with other shot blasted areas. The edging process is dry and produces minimal dust and airborne contaminants
Cleanup and disposal of dust is quick and easy
Available in both 110V or 220V models

Production capacity: up to 215 ft. square feet per hr
Cleaning Path: 8"
Travel Speed: Manually propelled
Voltage: 230 Volts, single phase, or 110 Volts, single phase
Amperage: 17A
Length: 3' 11"
Width: 1'
Height: 3' 3"
Weight: 181 lbs.

BMS 270 Deckabrator

floor scraping machine is ideal for removing VCT, marble, ceramic tile, glue-down carpet, and wood flooring. This propane-powered, one piece, ride-on unit features a small turning radius for maneuverability. It features an interchangeable scraping blade (available in 2 to 24 inch widths) or 2-inch breaker tooth (standard) for ceramic tile,marble, wood and other difficult removal applications. An optional pivot head attachment allows the scraping blade to rotate as much as 3 inches, maintaining consistent contact with uneven floors and surfaces.

Model 1 - 10D

Labor and time-saving shot blasting process strips, cleans and profiles simultaneously
Flooring surface is left dry and chemical-free without releasing airborne dust or contaminants
Drying times, acid etching and costly disposal procedures are eliminated
Blast pattern accuracy and wide abrasive selection allows users to achieve any desired surface profile
Excellent bonding characteristics are produced reducing coating failures, and maximizing floor life
Disposal of dust and contaminant is easily achieved
Recommended method of surface preparation by most coating manufacturers.

Production Capacity: Up to 1,000 square feet per hour
Cleaning Path: 10"
Travel Speed: 0-85 ft./min.
Voltage: 230 Volts or 460 Volts, 3 phase
Length: 5' 3"
Width: 1' 5"
Height: 3' 4"
Weight: 706 lbs

Model 1 - 10DE99

High-efficiency separation system provides a high degree of dust removal while reducing the amount of wear on the machine. High-production jet pulse dust collector allows you to connect hand operated surface preparation tools while using the blast head
Compact, light-weight design allows two persons to handle the equipment in and out of the transport vehicle. Easy setup at job site. Designed to achieve high production rates for low start-up cost. Incorporates a clean edge for preparing a surface as close as 1" from an obstruction.

Cleaning Path: 10"
Travel Speed: 0-80 ft./min
Voltage: 230 or 460 Volt, 3 phase
Amperage: 12 FLA (@ 460 V), 24 FLA (@ 230 V)
Length: 60"
Width: 16"
Height: 42"
Weight: 425 lbs.
Vacuum: Ideally used with the new 4-54 Dust Collector and 50 feet of 50 feet of 3" diameter hose.

Model 1 - 15D Super

Labor and time-saving shot blasting process strips, cleans and profiles simultaneously. Flooring surface is left dry and chemical-free without releasing airborne dust or contaminants. Drying times, acid etching and costly disposal procedures are eliminated. Blast pattern accuracy and wide abrasive selection allows users to achieve any desired surface profile. Excellent bonding characteristics are produced reducing coating failures, and maximizing floor life. Disposal of dust and contaminants is easily achieved. Recommended method of surface preparation by most coating manufacturers

Production Capacity: Up to 1,700 square feet per hr.
Cleaning Path: 15"
Travel Speed: 0-85 ft./min.
Voltage: 460 Volts, 3 phase
Length: 6' 7"
Width: 1' 11"
Height: 3' 6"
Weight: 850 lbs.

Model 2 - 20D

Labor and time-saving shot blasting process strips, cleans and profiles simultaneously. Flooring surface is left dry and chemical-free without releasing airborne dust or contaminants. Drying times, acid etching and costly disposal procedures are eliminated. Blast pattern accuracy and wide abrasive selection allow users to achieve a desired surface profile. Excellent bonding characteristics are produced, reducing coating failure and maximizing floor life. Disposal of dust and contaminants is easily achieved. Recommended method of surface preparation by most coating manufacturers.

Cleaning Path: 20"
Travel Speed: 0-108 ft/minl
Blast Motor: 30 hp
Voltage: 460V, 3ø, 60 Hz
Amperage: 47.7A
Total System Current: 61.9A*
Power Cord Length: 55'
Dimensions: 75"L x 30"W x 47"H
Weight: 1,235 lbs.

* total system current for blast unit and dust collector
8-54 Dust Collector

Voltage: 460V, 3ø, 60 Hz
Amperage: 14.2A
Power Cord Length: 75'
Vacuum Hose Length: 50'
Dimensions: 75"L x 42"W x 58"H
Weight: 1,235 lbs without hose

Model 2 - 30D

High production rates-up to 4,850 square feet per hour on concrete. Thirty inch blast pattern maximizes operator productivity. Magnetic seal minimizes abrasive loss during blasting. One-piece blast wheels designed for quick change. High-speed travel switch allows quick turn-around without resetting travel speed
Heavy-duty drive motor with brake for ramps and inclines. Powerful, automatic, pulse cleaning, cartridge dust collector with built-in compressor minimized dust and airborne contaminants. Large dust hopper equipped with wheels and handle makes disposal of dust quick and easy. All system components fit through standard doors. Recommended method of surface preparation by most coating manufacturers.

Production Capactiy: Up to 4,850 square feet per hr.
Cleaning Path: 30"
Travel Speed: 0-92 ft/min.
Power Cord Length: 60'
Voltage: 460 Volts, 3 phase
Amperage: 40A
Length: 6' 3"
Width: 3' 3"
Height: 4'
Weight: 1375 lbs.

Model GPX 10 - 18HO

Labor and time-saving shot blasting process strips, cleans and profiles simultaneously. Surface is left dry and free of chemicals, airborne dust and contaminants
Drying times and costly disposal procedures are eliminated. Blast pattern accuracy and wide abrasive selection allows users to achieve a desired surface profile. Excellent bonding characteristics are produced reducing coating failures and maximizing floor life
Recommended method of surface preparation by most coating manufacturers.

Production Capacity: Up to 1500 square feet per hour
Blast Pattern: 10"
Shot Hopper Capacity: 100 lbs
Engine: Kohler 25 h.p.
Fuel: Gasoline (unleaded); Propane (vapor)
Fuel Capacity: 6.5 gal. (gasoline); 33.5 lbs. (propane)
Drive: Hydrostatic transmission
Travel Speed: 0-200 ft./min.
Shot Valve: Electric actuator
Seal Lift System: Electric actuator
Ignition System: 12 Volt DC
Length: 78"
Width: 34"
Height: 57"
Weight: 1516 lbs.
Shipping Weight: (pallet) 1900 lbs.
Shipping Weight: (crate) 2100 lbs